Technical advice: 021 450 60 70 · Delivery nationwide · Blog

BFT Store
021 450 60 70 Contact

Installation and service for automation details

Product categories
Flashing light BFT: 24 V or 230 V and where you mount it

Automation accessories

Flashing light BFT: 24 V or 230 V and where you mount it

A flashing light BFT announces through intermittent light that gates, barrier or door garage starts. It matters because people around them observe time maneuvers, and the right choice between the 230 V and 24 V models depends directly on the central automation.

In short: B LTA works at 230 V and RADIUS B LTA 24 works at 24 V and has a built-in antenna; the voltage dictates the central gate.

Do you need help choosing?

Tell us what you need and we'll send you the offer on the same working day.

A well-chosen lamp makes every maneuver visible to neighbors, pedestrians and drivers. Starts from the voltage of the power plant: B LTA for 230 V, RADIUS B LTA 24 for 24 V automations. Mount the lamp to a high point, visible in both directions, and use the wall bracket when you need it. See both models in the flashing lights category and ask for the help of the BFT Store team if you don't know which center you have. A visual check at a few months completes the care.

A flashing light BFT visually warns that the gates, barrier or automatic door is starting to move. Thus, pedestrians and drivers observe the movement before the gate sheet reaches them. Both models in the category signalling lamps emits intermittent light, but works at different voltages.

Role of the lamp in automation

Any automation moves a large metal mass. Therefore, intermittent light sends a simple message: attention, follow a maneuver. Especially at night, the lamp becomes the first sign that the gates are starting. Also, many installers use it as an operating indicator, as it shows immediately whether the plant has received command.

However, a flashing light BFT does not replace security cameras or tapes. In other words, the lamp warns, and the safety devices stop or reverse the movement.

230 V or 24 V flashing light BFT?

The pressure of the lamp shall correspond to the lamp output from the control unit. Model BFT B LTA of 230 V is compatible with the automations that supply the lamp to the voltage of the network. Instead, BFT RADIUS B LTA 24 works at 24 V, i.e. at the voltage of low voltage BFT engines.

  • Engines with BT suffix, such as Deimos BT or Phobos BT, normally use 24 V.
  • The AC suffix variants, e.g. Deimos AC A600, work at 230 V.
  • The plant decides, however, what lamp you accept, so you check her manual.

So a flashing light BFT chosen wrong either does not turn on or quickly fails. For this reason, note the model of the power plant before ordering.

If you change automation, don't assume the old lamp goes on. For example, switching from a 230 V motor to a 24 V motor also changes the voltage of the lamp. Thus, you replace a flashing light BFT with the power plant, if the voltages differ.

Integrated antenna to the BFT RADIUS lamp

The RADIUS B LTA 24 has a built-in antenna. Practically, the lamp usually sits at the highest point of the pole or wall. Therefore, the antenna there captures the signal of the remotes better than a short wire near the power station. In addition, a flashing light BFT with antenna exempts you from a separate accessory.

If the chosen lamp has no antenna or the receiver stays away, you can mount antenna BFT AEL 433, which comes with 4 meters of cable.

Where you mount a flashing light BFT

The position of the lamp decides how useful it becomes. First, choose a visible place of both senses, i.e. of the street and the yard. Then avoid branches, bright companies or corners that hide it. The RADIUS sheet mentions that light remains easily visible even in environments with strong light. However, a good angle of view matters as much as intensity.

  • On the pole of the gate, at the height of the head or above.
  • Above a door garage, centered on opening.
  • Near a barrier, oriented towards the direction from which the cars come.

For wall mounting, use BFT wall support for RADIUS lamps. Thus, a flashing light BFT gets on the front, not just on the top of the pole.

Wiring and verification after assembly

The lamp receives power from the dedicated terminals of the plant. Therefore, use the cable with the section of the automation manual. Then start a complete cycle and watch if the light blinks throughout the movement. Some power plants allow and warning, i.e. the lamp blinks a few seconds before the engine starts. In this case, activate the function of the menu or DIP switches.

Finally, check the sealing of the cap after the first rains. A flashing light BFT with water inside gives an irregular signal or turns off.

How to keep a BFT RADIUS lamp visible

The lamp sits out all year, so the dust and insects gather on the dome. Therefore, clean the cap with a damp cloth at a few months. Also, check if any of the creases grew up in front of her. Especially after the storms, look at the fixing and the cap lining. If the light looks weaker, ask for a check at the next review. In addition, a clean flashing light BFT is much better seen in days with strong sun.

  • Clean the dome without aggressive solvents.
  • Press the screws of the holder after winter.
  • Test the lamp at each automating revision.

BFT warning lamp in the safety assembly

The safety of an automation comes from several elements that work together. For example, BFT photocells detect obstacles in the way of the gate, and the lamp announces maneuver. Set AKTA A30 has a radius of 30 metres and a horizontal adjustment of 180°. On the other hand, the category parts various accessories BFT complete the assembly. For general principles for the prevention of accidents with moving equipment, consult European Agency for Safety and Health at Work. In conclusion, a flashing light BFT works best alongside the photocells.

Frequently asked questions: flashing light BFT

Can I use the 24 V lamp at a 230 V automation?

No, unless the power plant has a 24 V lamp output. First check the connection scheme in the manual.

Does the lamp work with other automation marks?

The RADIUS file describes it for BFT automation. However, with the right voltage, many installers use it on other power plants after checking out.

Why does the lamp blink without the gates moving?

This is usually an error or a warning signal. Therefore, please refer to the error codes in the manual.

What flashing light BFT do I choose for a barrier?

You're still choosing after the voltage of the barrier plant. For example, a barrier with a 24 V power plant requires the RADIUS B LTA model 24.

Compare the two models in the category signalling lamps and choose after the voltage of your power plant. The BFT Store team helps you find a flashing light BFT compatible with the automation you have.

Recent articles

All articles

Cookie settings

Choose which categories you accept. Strictly necessary cookies are always active; the others start only with your consent and you can change them at any time. Cookie policy

They make the site work: shopping cart, favourites, customer account sign-in, form security and remembering your cookie choice. They cannot be disabled.

Remembers recently viewed products so you can find them easily. The data stays only in your browser.

Shows us which pages are visited and how the site is used, so we can improve it (Google Analytics).